Odroid-HC4 Home Cloud with OLED 4GB RAM Amlogic S905X3 1.8GHz Quad Core

€132,38 €105,90

Download Odroid-HC4 Resources

Like the Odroid-C4, the Odroid-HC4 also features the 1.8Ghz Amlogic S905X3 ARM Cortex-A55 Quad-Core processor with Mali G31 MP2 Graphics Processing Unit. The HC4 is based on the Home Cloud platform. The memory on the board is DDR4 4GB RAM. The Odroid-HC4 comes with an SPI 16MiB flash chip with Petitboot support.

Note: This Odroid HC4 Version comes with the OLED  

What is new with Odroid-HC4

The Odroid-HC4 has a reliable SATA bridge solution (PCIe to SATA) instead of USB3.0 to SATA. This way, the HC4 supports 2x SATA storage docks. This board comes with a transparent case with cutouts for board interfaces and ports.

Video Presentation of the Product

Specifications of Odroid-HC4 Home Cloud

  • Processor
    • Amlogic S905X3 12nm
    • 32 KB L1 instruction cache, 128 sets 4-way set associative, 1 processor shares 64 byte lines
    • 32 KB L1 data cache, 128 sets 4-way set associative, 1 processor shares 64 byte lines
    • 512KB L3 data cache, 512 sets 16-way set associative, 4 processors share 64 byte lines
    • Architecture: ARMv8-A with Crypto and Neon extensions
    • Mali-G31 MP2 GPU (650MHz) 4x Execution Engines
  • RAM
    • 4GiB DDR4
    • But width: 32-bit
    • Data Rate: 2640 MT/s
    • Grade: PC4-21333
    • Low Power Design: 1.2Volt
  • Storage
    • 1x Micro SD Slot (Compatible with DS/HS mode and supports UHS-1 SDR104)
  • Networking
    • 1x RJ45 GbE LAN Port | supports 10/100/1000 Mbps
    • RTL8211F Realtek Ethernet Transceiver
    • Amber LED: 1000Mpbs connection data traffic indicator
    • Green LED: 100Mpbs connection data traffic indicator
  • Video
    • 1x HDMI 2.0 Port with HDR, EDID, CEC | up to 4K @ 60Hz
  • Audio
    • 1x HDMI Digital Audio Output
  • Heatsink
    • A passive heatsink on the processing unit
    • Dimensions: 40mm x 32mm x 10mm | 4cm x 3.2cm x 1cm
  • Cooling Fan
    • A Hydraulic Bearing Fan
    • Current Rating: 100 mA
    • Voltage Rating: 5V
    • Maximum Rotations Per Minute (RPM): 4000 Rotations
    • Air Pressure: 0.053 in H2O
    • Air Flow: 4.3 CFM
    • Noise Level: 23.9 dBA
    • Connector and Wire: 1.25mm Pitch 4-Pin, 80mm
    • Dimensions: 40mm x 40mm x 10.6mm | 4cm x 4cm x 1.06cm
  • External Input / Output
    • SATA Connectors (x2)
    • HOST USB 2.0 Port (x1)
    • UART Serial Debug Console (x1)
  • General
    • IR receiver for infrared remote control
    • System Indicator LEDs
      • RED LED for PWR (DC Power Connected)
      • BLUE (Flashes when Kernel is running)
    • Power
      • 1x DC Power Jack: 5.5mm (negative / outer) and 2.1mm (positive / inner) diameter
      • 5V ~ 15.5V DC Input
      • 15V / 4A DC Power Adapter Recommended (Not Included)
    • Power Consumption with 2x HDDs (ST2000DM006)
      • IDLE Mode: Approximately 5.88 W (when HHD is in Spin-Down)
      • Active Mode: Approximately 15.59 W (while using SAMBA)
      • Suspend Mode: Approximately 0.29 W
    • Form Factor
      • Dimensions of HC4 Board: 9.05cm x 8.4cm x 2.5cm | 90.5mm x 84mm x 25mm
      • Weight of HC4 (including the case, fan, and heatsink): 280 grams | 0.28 kg

Odroid-HC4 Software Compatibility

Petitboot is capable of automatically locating the Operating System on the SSD, HDD, or SD Card. It means that even if there is no SD Card attached, Petitboot will use the attached SSD or the HDD to boot the Odroid-HC4 if the Operating System is installed on any of the connected storage units. 

The preinstalled Operating System Image from Hardkernel is compatible with Ubuntu and Debian Operating Systems. You can also use the Ubuntu or Debian Netboot installer.

The Odroid-HC4 supports the following versions of Linux Kernel:

  • Hardkernel Stock Operating System version 4.9.230 or higher
  • Mainline Kernel (unofficial) version 5.8 or higher

Items Included

  • 1x Odroid HC4 with OLED

Compatible Items (Not Included)

Customer Reviews

No reviews yet
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)

Customer Reviews

No reviews yet
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)