2.9inch E-Ink Display Module (Black and White)
Click Here to download the complete user guide to working with Raspberry Pi, Jetson Nano, Arduino, Sunrise X3 Pi, and STM32 as well as resources and FAQs.
This is a 2.9-inch E-Ink Display Module compatible with the SPI communication interface. It is It features 296x128 pixels resolution and comes with an embedded controller with partial refresh support.
This innovative display technology supports partial refresh, making it an ideal choice for a wide range of applications.
- No backlight: Displays the last content for a long time even when powered down
- Ultra-low power consumption: Power is only required for refreshing
- SPI interface: Allows for easy connection with controller boards like Raspberry Pi/Arduino/Nucleo, etc.
- Onboard voltage translator: Compatible with 3.3V/5V MCUs
- Comes with development resources and manual: Includes driver board schematic and examples for Raspberry Pi, Jetson Nano, Sunrise X3 Pi, Arduino, and STM32
- Shelf label: Suitable for displaying product information, pricing, and promotions
- Industrial instrument: Ideal for displaying measurements and data in a wide range of industrial applications
- E-reader: Perfect for reading e-books and other digital content with a paper-like effect
- Smartwatch: Can be used to display notifications, time, and other relevant information on a smartwatch screen
Advantages of E-Paper (E-Ink) Display Technology
The E-Paper Display uses microcapsule electrophoretic technology to display content. This technology works by applying an electric field to charged particles suspended in clear fluid, causing the microcapsule to become visible by reflecting ambient light, just like traditional printed paper. Some of the benefits of this technology are:
- Clear display without electricity: Display content is clearly visible under lamplight or natural light without a backlight
- Wide viewing angle: Offers nearly up to 180° viewing angle
- Paper-like effect: Often used as an e-reader due to its resemblance to traditional printed paper
- Display Size (Diagonal): 2.9 inches
- Operating Voltage: 3.3V ~ 5V (for signals and power supply, 5V is required)
- Communication Interface: SPI (3-Wire and 4-Wire)
- Display Colour: Black and White
- Field of View: > 170o
- Resolution: 296 x 128 pixels
- Dot Pitch: 0.138mm x 0.138mm
- Grey Scale: 2
- Refresh Power (Typical): 26.4mW
- Refresh Time: 2 Seconds
- Partial Refresh Time: 0.3 Second
- Standby Power: <017mW
- Weight: 36 Grams
- VCC: 3.3V / 5V
- GND: Ground
- DIN: SPI MOSI Pin
- CLK: SPI SCK Pin
- CS: SPI Chip Selection (Low Active)
- DC: Data / Command Selection (Low for Command / High for Data)
- RST: External Reset (Low Active)
- BUSY: Busy Status Output (High Active)
- Outline Dimensions: 89.5mm × 38mm
- Screen Dimensions (Display Area): 66.89mm × 29.05mm
Connecting with Raspberry Pi and Other Boards
This e-Ink Display module can be connected to Raspberry Pi, Arduino, STM32, Jetson Nano, and Sunrise X3 Pi.
For Raspberry Pi, the module can be inserted into the 40PIN header or connected via an 8PIN cable. The SPI interface needs to be enabled and drivers' coverage needs to be closed. BCM2835 and WiringPi should be installed, and demo code can be downloaded via GitHub.
For Arduino, an 8PIN cable should be used to connect to the module, and the corresponding pins should be used according to the table provided. The demo code can also be downloaded via GitHub.
Please refer to the User Guide provided at the top to see the detailed guidelines to connect the module with Jetson Nano, Sunrise X3 Pi, and STM32!
- 9-inch e-Paper Display Module
- PH2.0 8Pin 20cm Wire